mailto:jay.hutchison at va dot gov] sent: friday, september 07, 2007 three:18 pm
to: emc networker discussion; lemons, terry
subject: re: [networker] windows2003 r2 switch tape order at boot query two? we've got 5 ibm ultrium iii drives in an adic scalar i500 installed to the neworker server and all ten storage nodes. all of them use a dell driver (ver. six.0.six.83)should certainly we switch to the ibm driver? -----original message-----
from: emc networker discussion [mailto:networker at listserv.temple dot edu] on behalf of terry lemons
sent: friday, september 07, 2007 3:03 pm
to: networker at listserv.temple dot edu
subject: re: [networker] windows2003 r2 switch tape order at boot hi jay the switch for the registry requirements for being manufactured about the system on which you install the tape drivers, which is the technique which has the tape drives, that is the storage node. jay's query reminded me of two dilemmas you could have when working using the ibm tape driver: 1. ibm created an, er, regrettable default setting from the ibm tape driver: support for information route failover and control route failover is enabled by default. but, when you do not have the license for these attributes set up, the driver just will not likely function. so, be sure that you use the .reg files provided with the driver to disable the cpf and dpf aspect before you are attempting to implement the driver
two. contrary to just about every other driver i've put to use on windows, the ibm tape driver cannot be installed using the typical system manager methodology. it have to be installed implementing the set up.exe program that arrives using the driver kit. fyi
tl terry lemons
backup platforms group
emc²
where information lives
4400 computer drive,
office 2007 Professional keygen, ms d239
westboro ma 01580
phone: 508 898 7312
email: lemons_terry at emc dot com -----original message-----
from: hutchison,
microsoft office Pro 2007 key, jay a [mailto:jay.hutchison at va dot gov]
sent: friday, september 07, 2007 2:50 pm
to: emc networker discussion; lemons, terry
topic: re: [networker] windows2003 r2 adjust tape buy at boot terry does the improve towards the registry need to become done about the clients as well as the networker server? -----original message-----
from: emc networker discussion [mailto:networker at listserv.temple dot edu] on behalf of terry lemons
sent: thursday, september 06,
windows 7 home basic 64 bit, 2007 4:32 pm
to: networker at listserv.temple dot edu
subject matter: re: [networker] windows2003 r2 change tape buy at boot hello pierpa i replied to your question (below) in a reply to another list posting. but, i wanted to comment on something you mentioned, below: "this tapes are connected through the san to a qlogic fc board on my server on two different ports." so, does your windows 2003 r2 method see the same tape library twice: one time each on two different fc hba ports? if so, that sounds like a problem, in that multi-pathing for tape devices is very, very rare. that said, the ibm ultrium tape driver does support multi-pathing for both the command route (to your autochanger system) and on the info route (to your tape drive). this is a licensed characteristic, and you need to pay ibm for the right to do this. this is described in ftp://ftp.software.ibm.com/storage/devdrvr/doc/ibm_tape_driver_iug.pdf for the operating systems that support it. look for references to 'control path failover' and 'data path failover'. hope this helps.
tl terry lemons
backup platforms group
emc²
where information lives
4400 computer drive, ms d239
westboro ma 01580
phone: 508 898 7312
email: lemons_terry at emc dot com -----original message-----
from: emc networker discussion [mailto:networker at listserv.temple dot edu] on behalf of pierpa
sent: thursday, september 06, 2007 7:03 am
to: networker at listserv.temple dot edu
subject: [networker] windows2003 r2 modify tape purchase at boot hi all,
i've a problem i'm not able to solve.
i'm making use of nw7.4 on a windows2003 r2 server with a adic scalar24 library with two tapes in fc. this tapes are connected through the san to a qlogic fc board on my server on two different ports. i've put in oem ibm drivers for my lto3 drives but sometimes,
windows 7 enterprise activation key, rebooting the server, the buy of the tapes changes. therefore the library is confused, thinking to manage tape1 instead of tape0 and viceversa. i don't know on windows and on qlogic if i can establish the tapes order. may possibly i use on windows something like persistent binding ? any suggestion will be appreciated pierp to sign off this list, send email to listserv at listserv.temple dot edu and type "signoff networker" within the body of the email. please write to networker-request at listserv.temple dot edu any time you have any issues with this list. you can access the archives at or via rss at to sign off this list,
microsoft office 2010 sale, send email to listserv at listserv.temple dot edu and type "signoff networker" inside body of the email. please write to networker-request at listserv.temple dot edu should you have any complications with this list. you can access the archives at or via rss at to sign off this list, send email to listserv at listserv.temple dot edu and type "signoff networker" within the body of the email. please write to networker-request at listserv.temple dot edu if you happen to have any problems with this list. you can access the archives at or via rss at to sign off this list, send email to listserv at listserv.temple dot edu and type "signoff networker" inside the body of the email. please write to networker-request at listserv.temple dot edu if you happen to have any complications with this list. you can access the archives at or
via rss at
microsoft office Pro 2007 key re [networker] wind
Linear Mode
